Network wiring training device

Network wiring tr--ning device,Cross Slide Control Tr--ning Device

1. Technical specifications:

Shape size: 600mm long, 530mm wide, high 1800mm high

Voltage/power: AC 220V/50W

Supporting equipment: 6U network pressure wiring experimental 1, 6U network jumping line detection and f--lure demonstrator, 2 network rag ring ring, 8 PDU power sockets, 100 rounds 110 communication jumping line frames, 2 units Two network wiring racks, 1 optical fiber wiring frame, 1 part/tool box, and 1 set of power areas.

2. Product characteristics

1) The device is selected from the 19 -inch open floor frame. The shape size: 0.6 meters long, 0.53 meters wide, 1.8 meters high. The lower part of the rack is fixed to the foot screws, ensuring that the equipment is firm and can withstand the impact of tr--ning lines.

2) 6U rack type color LED color block display function network pressure wiring tr--ning tester (color LED color block display light, a total of 96), each core wire is connected to the corresponding color LED light block, intuitive continuous display display display The connection status and line order of the end connection. There are 96 luminous colors in 48 groups. At the same time, all end connection conditions of the six twisted lines are displayed, and it is intuitively judged that the cross -connection, anti -connection, short circuit, and disconnection of the communication network twisted line. The test results were transmitted to the Teacher's computer management side software with the WiFi wireless signal or RS485.

One of the network jumping line detection and fault demonstrators of the color LED display function, corresponding to the connection status and line order of the colored LED light luminous block display of the two ends of the RJ45 connector. Each jump corresponds to the 16 colored LED luminous color blocks of 8 groups, and the connection status and line order are visually continuously displayed. It is divided into 32 groups with 64 luminous color block lamps, and there are cable types, groups, and fault type prompt lamps. , Quickly detect 4 jumper pressure connections at the same time. F--lure simulation demonstration functions, set 6 groups (correct, anti -connection, cross, interruption, cross, short circuit) common network wiring correct and fault types. The test results were transmitted to the Teacher's computer management side software with the WiFi wireless signal or RS485.

4) Teacher teaching design system (providing demonstration and copyright certificate): This system is the format of the APK, which can be used on the PC side or on the mobile terminal. This system can be manually set up manually and can be automatically set up. Select the green box in the circuit diagram to manually set the fault point (*** can set up 39 fault points). You can also automatically perform a random f--lure point settings through the system, two fault points settings, random three fault points settings, random point settings, random point settings, random point settings, random point settings settings, random three f--lure points settings, random point settings. Randomly four fault points settings, random fault points settings, have toolboxes, component libraries, magnifying glass, circuit diagrams and other functions in this system. You can choose a multimeter to detect through the toolbox. You can clearly understand each component and circuit. This system starts the control circuit f--lure through the motor star triangle, and has been investigated to allow students to understand the working principle and circuit structure of the motor star triangle to start the control circuit.

Network wiring tr--ning device,Cross Slide Control Tr--ning Device

Note: You can configure PLC separately, or you can use the PLC tr--ning device to use

Overview

This device is the micro -shrinking of the actual flat two -dimensional motion system. It is controlled by a programmable controller. In the direction of the X and Y axis, it accurately drives the stepping motor to perform the finished product control. All the action processes in the system.

Technical Parameters

Power: single phase AC220V, 50Hz

Power: <200W

Size: not less than 600*400*500mm

Equipment structure:

The cross -sliding control tr--ning model is a metal structure, and the connection terminals of each commonly used module are connected to the safe socket, and the circuit is connected to the circuit with a wire with a safe plug; connect. The combination of the plug -in connection circuit with the terminal connection circuit not only ensures the tr--ning, formation and consolidation of the basic skills of students, but also to ensure the rapid, safe and reliable circuit connection.

3. Equipment characteristics:

1. Manual/automatic control mode, for hardware detection and programming.

2. Open execution agencies can be programmed according to different control schemes to form different execution systems, and adapt to personnel at different levels to learn and program. It can also be used as a subject design or research.