Construction Machinery Electric Control Diesel Engine Training Device

Construction Machinery Electric Control Diesel Engine Tr--ning Device,Battery wind and cold water show teaching and tr--ning device

1. Product introduction

This device uses a refurbished construction machinery/Bosch 2.8T electrical control high -voltage -r--l diesel engine. It can perform practical operations such as starting, accelerating, and deceleration. process.

It is suitable for the school's teaching needs for electronic control high -voltage co -r--l engine and m--ntenance tr--ning.

2. Functional characteristics

1. The real -operated electrical control high -voltage common r--l diesel engine (acceleration/deceleration/idle work condition is normal), and fully display the structure and working process of the electronic control high -voltage r--l diesel engine.

2. The tr--ning table panel adopts the 4mm thick corrosion resistance, strike, pollution resistance, fire prevention, and moisture -proof ** aluminum -plastic panels. The surface is sprayed with primer p--nting by special processes; Intuitive control circuit diagrams and electronic control high -voltage co -r--l diesel engines, understand and analyze the working principle of the control system.

3. The tr--ning terminal is installed on the panel, and the electrical signals that can detect each sensor, actuator, and engine control unit pipe foot can be detected directly on the panel, such as resistors, voltage, current, frequency signals, etc.

4. The tr--ning countertop is installed with a car instrument, which can display the changes in the engine speed, water temperature, oil pressure lamp, charging indicator, and electrical control system fault indicator light in real time.

5. There is a diagnostic seat installation of the tr--ning desk, which can be connected to a dedicated or universal car decoder to read the engine electrical control system to read the fault code, clear the fault code, and the data flow.

6. The tr--ning table is equipped with a throttle control device, which can be convenient to accelerate the engine.

7. The tr--ning desk is equipped with installation protection devices such as total power switch, water tank protective cover, and flywheel protective cover.

8. The device detection panel is equipped with a 20cm steel table on the front base in front, which is convenient for placing data and detecting instruments.

9. The base of the tr--ning platform is welded with steel structure, and the surface is treated with spraying process. The front/sides are welded with a circular hand rod with a self -locking wheel device. It is flexible, safe, reliable, and durable.

Construction Machinery Electric Control Diesel Engine Tr--ning Device,Battery wind and cold water show teaching and tr--ning device

1. Product introduction

The device uses the new energy vehicle power battery water cold heat dissipation system (ESS), which fully demonstrates the composition and work process of the new energy vehicle power battery water cold and cooling system. It is suitable for the teaching needs of the school's theory and m--ntenance tr--ning for new energy vehicle power battery water cold heat dissipation systems.

2. Functional characteristics

1. The new energy vehicle power battery water cold and cooling system that runs the demonstration fully shows the composition of the new energy vehicle power battery water cold heat dissipation system.

2. Operation control switch to demonstrate the working process of the cold and cooling system of the new energy vehicle power battery water, and install the working process of the flashing light -emitting diode synchronous display system.

3. The panel uses a 4mm thick aluminum plastic panel, and the panel UV tablet inkjet is printed with color map boards. Students can intuitively compare the map boards and physical objects to understand and analyze the working principle of the system.

4. Electrical signals that detect terminals on the panel and can directly detect system circuit components on the panel, such as resistors, voltage, current, frequency signals, etc.

5. The device is constructed by the vertical mobile teaching board (with the original facial teaching board) and the horizontal placement platform (the m--n components of each installation system).

6. The equipment framework is built with 40mm × 40mm and 40mm × 80mm. With 4 self -locking devices universal foot wheels for easy movement.

7. Supporting tr--ning guidance books and other teaching materials, completely tell the m--n points of working principles, tr--ning items, fault settings and analysis.

8. Machinery assembly and fitter assembly virtual simulation software: This software is developed based on Unity3D, which can choose 6 -level image quality. It has the design and virtual disassembly of the reducer and shaft structure, the design and simulation of common mechanical mechanisms, institutional resource libraries, institutional resource libraries. Typical mechanical institutions (virtual disassembly of gasoline engines), software is an overall software, which cannot be separate resources.