DYQCF-2 diesel engine running experimental device

Release time：2024-06-03 13:00viewed：times

1. Product Introduction
This equipment is based on a diesel engine. It can run the engine, carry out practical operations such as starting, acceleration, deceleration and other working conditions, and truly demonstrate the composition and working process of an ordinary diesel engine.

2. Functional features
1. A real and operational ordinary diesel engine, fully demonstrating the composition and working process of an ordinary diesel engine.
2. The tr*ning table panel is made of 4mm thick high-grade aluminum-plastic panels that are corrosion-resistant, impact-resistant, pollution-resistant, fire-proof, and moisture-proof. The surface is sprayed with primer using a special process; the panel is printed with color circuit diagrams that will never fade; students can intuitively Compare the circuit diagram and the actual diesel engine to understand and analyze the working principle of the control system. 3. A car
instrument is installed on the panel of the tr*ning platform , which can display changes in parameters such as engine speed, water temperature, oil pressure light, and charging indicator light in real time. 4. There are detection terminals installed on the panel of the tr*ning platform, which can directly detect the electrical signals of each relay, solenoid valve, sensor and other pins on the panel , such as resistance, voltage, current, signal, etc. 5. The tr*ning platform is equipped with a throttle control device to facilitate acceleration and deceleration of the engine. 6. The tr*ning platform is equipped with m*n power switch, water tank protective cover, flywheel protective cover and other installation protection devices. 7. The base of the tr*ning platform is welded with a steel structure, and the surface is spray-p*nted. It is equipped with a self-locking caster device, which makes it flexible to move, safe, reliable, sturdy and durable. 8. Mechanical assembly and fitter assembly virtual simulation software: This software is developed based on unity3d, with optional 6-level image quality. It is equipped with the design and virtual disassembly and assembly of reducers and shafting structures, the design and simulation of common mechanical mechanisms , and a mechanism resource library. For a typical mechanical mechanism (virtual disassembly and assembly of a gasoline engine), the software is a whole software and cannot be individual resources. A. Reducer design and virtual disassembly interface can choose worm gear bevel gear reducer, two-stage expanded cylindrical gear reducer, bevel cylindrical gear reducer, coaxial cylindrical gear reducer, bevel gear reducer, and one-stage cylindrical gear reducer. Gear reducer. Worm bevel gear reducer: After entering the software, the assembly content is automatically played. Each step in the video has a text description . Secondary expandable cylindrical gear reducer: After entering the software, the content is played in the form of a video. The video content should include: Part name ( Scan the QR code to see the names of parts), disassembly and assembly demonstration (including disassembly and assembly), virtual disassembly (including overall, low-speed shaft, medium-speed shaft, high-speed shaft, box cover, box seat) conical cylindrical gear reducer, Coaxial cylindrical gear reducer, bevel gear reducer, first-level cylindrical gear reducer: click to enter and automatically jump to the edrawings interface. The models are all three-dimensional models. By clicking on the parts, the names of the parts are displayed, and the 360° view is av*lable Rotate, zoom in, zoom out, pan, and move parts to disassemble and assemble the entire reducer. At the same time, you can select the home button to return to the original state of the reducer. The bevel gear reducer and the first-stage cylindrical gear reducer have added the function of inserting a cross section, and the cross section can be freely dragged to observe the internal structure of the reducer. B. Shaft structure design and virtual disassembly and assembly interface optional parts recognition, disassembly and assembly demonstration, and actual operation. 1. Parts recognition: three-dimensional model and part name including helical gear, non-hole end cover, coupling, coupling key, shaft, gear key, hole end cover, shaft sleeve, deep groove ball bearing, any All parts can be rotated 360° 2. Disassembly and assembly demonstration: There are 2 built-in cases. When you move the mouse to the position of a cert*n part (except the base and bearing seat), the part will automatically enlarge and the name of the part will be displayed. It is equipped with disassembly and Assembly button, the function is to automatically complete the disassembly and assembly of the shaft system structure by the software. All three-dimensional scenes can be rotated, enlarged, reduced and translated 360° in all directions. 3. Practical operation: The three-dimensional parts are neatly placed on the table. Students manually select the corresponding parts and move them to the shaft system structure. The parts can be installed only when they are placed in the correct order and in the correct position. There is a restart button to facilitate students to restart. Conduct virtual experiments. When you move the mouse to a cert*n part position (except the base and bearing seat), the part will automatically enlarge and the part name will be displayed. C. Common mechanical mechanism design and simulation, optional hinge four-bar mechanism design and analysis, I\II type crank rocker mechanism design and analysis, offset crank slider mechanism design and analysis, crank swing guide rod mechanism design and analysis, hinge Four-bar mechanism with integrated trajectory, eccentric linear-acting roller push rod cam , and centering linear-acting flat-bottomed push rod cam. 1. Each mechanism should be able to input corresponding parameters, and the software can automatically calculate the parameters, and can perform motion simulation and automatically draw curves. D. The mechanism resource library includes 11 types of planar link mechanisms, 5 types of cam mechanisms, 6 types of gear mechanisms, 8 types of transmission mechanisms, 11 types of tightening mechanisms, 6 types of gear tr*n mechanisms, and 8 types of other mechanisms (mechanical equipment simulation) E , virtual disassembly and assembly of gasoline engines, optional crankcase assembly and disassembly demonstration, crankcase virtual assembly, valve tr*n assembly and disassembly demonstration, valve tr*n virtual assembly 1. Crankcase assembly and disassembly demonstration and valve tr*n assembly and disassembly demonstration both have disassembly button, assembly button, restart, and decomposition observation button. When the mouse is moved to a cert*n part position, the part will automatically enlarge and the part name will be displayed. The software automatically completes the disassembly and assembly of the shaft system structure. When using the decomposition observation button, the 3D model of the crankcase or gas distribution system automatically displays an exploded view, which can be rotated, enlarged, reduced, and translated 360°. 2. The 3D parts of the crankcase virtual assembly and the gas distribution system virtual assembly are neatly arranged When placed on the desktop, students manually select the corresponding parts and move them to the mechanism. The parts can be installed only when they are placed in the correct order and in the correct position. There is a restart button to facilitate students to re-perform the virtual experiment. When you move the mouse to cert*n part locations, the part names are automatically displayed. 3. Technical specifications Overall dimensions: 1500×1000×1700mm (length×width×height) Working power supply: DC 12V Fuel label: According to engine model Fuel tank volume: 10L Working temperature: -40℃～+50℃ Color: 7032
Steel pipe: 40*40*3mm
Panel cabinet: 1.5mm cold plate stamping and forming, m*ntenance door set on the back;
Mobile casters: 120*80mm
IV. Basic configuration (each unit)

serial number	name	Specifications and models	unit	quantity
1	Test control panel	Equipped with various detection terminals and color circuit diagram (9509004mm aluminum-plastic plate)	set	1
2	instrument cluster	Original car	set	1
3	Ignition Switch	Original car	indivual	1
4	Ordinary diesel engine assembly	Original car	set	1
5	Fuel tank	10L	indivual	1
6	Throttle control		set	1
7	Intake and exhaust pipes (with protective cover)	Original car	set	1
8	Water tank (including st*nless steel protective cover)		set	1
9	battery	12V 80Ah	tower	1
10	relay	Including: starting relay, preheating relay, etc.	set	1
11	Fuse box		indivual	1
12	m*n power switch	50A	indivual	1
13	Mobile stand (with self-locking casters)	1500×1000×1700mm (length×width×height)	tower	1
14	Fault simulation and troubleshooting device		set	1
15	Equipment Teacher's Manual		set	1
16	Equipment certificate, warranty card		set	1

Previous：DYQCF-3 high-voltage common rail diesel engine maintenance experimental device

Next：DYQCF-1 electronic control gasoline engine running experimental device